Dolby Laboratories DM100 Instrukcja Użytkownika Strona 15
- Strona / 65
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Dolby
®
DM100 User’s Manual Getting Started
2-7
2.6 Quick Start
The DM100 is designed to be easy and intuitive to use. Follow
these simple procedures to begin taking your first readings and
generating your first test streams.
Making Your First Reading
1. Turn on the unit by pressing [Power].
2. Connect the input signal to the appropriate connector.
3. Press [Mon]. This resets all the internal monitoring setup
functions to the defaults.
The LEDs should display the signal type received, and the
display shows information about the incoming signal. If you
cannot see this information, press [Status], then use [Enter],
[Esc], and the [Up/Down] buttons to navigate through the status
menus to view information about the incoming signal. See
Section 3.2 for additional information.
Adjust the audio level with the dedicated [Volume] buttons.
Generating a Bitstream
1. Press [Gen] once. This turns the generator on and outputs a
PCM test signal.
2. To select other test streams, continue to press [Gen].
Different clock sources can be used for the generator; these can
be selected in the Gen Clock Source menu:
Setup / I/O Control / Gen Clock Source
See Section 4.5 for more information.
To read the current status of the generator, press [Status] and
navigate using the [Down] button until Generator Enter to
View is displayed. Press [Enter] to see the current settings. See
Section 3.2.5 for more information.
You can even connect the output of the DM100 to the input.
Doing this allows you to listen to the test stream and view all of
the streams’ settings.
- '0%LWVWUHDP$QDO\]HU 1
- DM100 Bitstream Analyzer 2
- Dolby Laboratories, Inc 3
- Table of Contents 4
- DM100 User’s Manual 5
- Chapter 1 8
- Introduction 8
- Chapter 2 9
- Getting Started 9
- 2.2 Rear Belt Clip/Stand 11
- 2.3 Inputs 12
- 2.4 Outputs 13
- 2.5 Hookup 14
- 2.6 Quick Start 15
- 2.7 Advanced Features 16
- Chapter 3 18
- Operation: Status Mode 18
- Dolby E B 19
- 5.1+2 24bit 19
- 3.2 The Status Menus 22
- (depending on Dolby E 23
- Px Line Mode Pro 23
- Px RF Ov Protect 23
- [Enter] 23
- If actual dynamic range 26
- J J J 26
- If dynamic range control 26
- Dolby Digital MD 31
- ENTER to View 31
- DD Stream # 40
- 3.2.3 AES3 Status Menu 41
- A = bit 4 of byte 22 41
- B = bit 5 of byte 22 41
- C = bit 6 of byte 22 41
- D = bit 7 of byte 22 41
- 3.2.4 Input Level Menu 43
- Digital Full-Scale 43
- Frame Rate 45
- No video input 45
- Timecode xx Dly 46
- 00:00:00:00 N/A 46
- 3.2.8 Error Stats Menu 47
- 3.2.9 DM100 Firmware Version 48
- Chapter 4 49
- Operation: Setup Mode 49
- 4.1 Monitor Control 50
- 4.2 Gen Control 52
- When generating PCM 53
- Sine or Square waveform 53
- 4.3 AES3 Output 54
- 4.4 User Presets 56
- 4.5 I/O Control 57
- 4.6 System Settings 58
- Chapter 5 60
- Reference Information 60
- 5.2 Unit Reset 62
- 5.3.1 RS-232 Serial Port 63
- 5.3.2 XLR Connectors 63
- 5.3.3 Headphone Connector 63
- 5.4 DM100 Specifications 64
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Dolby Laboratories DM100
(2 strony)Winco WL12000HE/K manuales
Manuales del propietario y guías del usuario para Equipo Winco WL12000HE/K.
Ofrecemos 1 manuales en pdf Winco WL12000HE/K para descargar gratis por tipos de documentos: Manual de usuario
Komentarze do niniejszej Instrukcji